 |
HY-5050-60LED
DC12V
14.4w
white/red/green/blue
IP20
3years
120Degree
| Quantity: | |
|---|---|
LED Motion Sensor5050 12V Flex Decoration LED Light Strip
select and use TOP5050led light source, without spot, low light decay, good consistency
Products with low power consumption, high brightness, long life, maintenance-free
use double side flexible PCB, beautiful appearance, good cooling effect
IP20 waterproof rating up above
Low voltage input, safe and reliable(DC12V)
5METERS/ROLL, 3leds one point can be cutted
Advertising signs, illuminqted signs ,slim boxes, plastic characters. Etc
1. Installation method of flexible light bar
1. Tear 3M glue
There is a self-adhesive 3M double-sided adhesive on the back of each LED flexible light bar, which can be torn off directly when installing, and then fix the light bar in the installation position and stick it tightly by hand.
2. Cut the length of the LED strip at will
As for some places that need to be turned or the length of the LED light bar is inconsistent. The circuit structure of the LED light bar is composed of 3 LEDs in series and parallel, and each 3 LEDs can be welded or cut at will.
3. Fixing of flexible light bar
If it is installed outdoors, it will be easily affected by the outside world, which will affect its use. Over time, the decrease of 3M adhesive will cause the LED light bar to fall off, so fix it with a card slot. The place that needs to be connected and cut is the same as the indoor installation method, only need to be equipped with waterproof glue to strengthen the waterproof effect of the connection point.
4. Power supply for flexible light bar
The general voltage of the LED flexible light bar is DC 12V, so a switching power supply is required. The size of the power supply is calculated according to the length and power of the LED flexible light bar. You can also buy a high-power switching power supply as the main power supply, and connect all the LED flexible light bar input power in parallel, and the main switching power supply is used to supply power.
5. Use amplifier for LED flexible light bar
If the connection distance of the LED light bar is long, and the controller cannot control that long light bar, it is necessary to use a power amplifier for tapping.
6. Power connection method of LED flexible light bar
LED light bars generally have three voltages: AC220V, DC12V, and DC24V, so you need to choose a suitable switching power supply. The size of the power supply is determined by the power and connection length of the LED light bar. Monochrome 3528 patch and 5050 patch, the wiring method of LED lights DC24V and DC12V is as follows: black wire replaces negative "-", red wire replaces positive "+", and a soldered "red and black" power cord is provided, Just plug it directly into the light strip switching power supply provided. The black wire is connected to the negative "-" of the switching power supply and the "red" color wire is connected to the positive "+" of the switching power supply.
question&answers:
Q: Which led chips are used in this type module?
A: 22Lumen SMD5050 used for this type
Q:What Controller for this type strip?
A:very single color
Q:How many quantities module in one Roll?
A:5meters/15meters/50meters
Q:How long can i get the sample?
A: need 3-5days to send sample.
Q: Do you have MOQ limit for order ?
A:Not limit the MOQ. just depend on clients demand.
LED Motion Sensor5050 12V Flex Decoration LED Light Strip
select and use TOP5050led light source, without spot, low light decay, good consistency
Products with low power consumption, high brightness, long life, maintenance-free
use double side flexible PCB, beautiful appearance, good cooling effect
IP20 waterproof rating up above
Low voltage input, safe and reliable(DC12V)
5METERS/ROLL, 3leds one point can be cutted
Advertising signs, illuminqted signs ,slim boxes, plastic characters. Etc
1. Installation method of flexible light bar
1. Tear 3M glue
There is a self-adhesive 3M double-sided adhesive on the back of each LED flexible light bar, which can be torn off directly when installing, and then fix the light bar in the installation position and stick it tightly by hand.
2. Cut the length of the LED strip at will
As for some places that need to be turned or the length of the LED light bar is inconsistent. The circuit structure of the LED light bar is composed of 3 LEDs in series and parallel, and each 3 LEDs can be welded or cut at will.
3. Fixing of flexible light bar
If it is installed outdoors, it will be easily affected by the outside world, which will affect its use. Over time, the decrease of 3M adhesive will cause the LED light bar to fall off, so fix it with a card slot. The place that needs to be connected and cut is the same as the indoor installation method, only need to be equipped with waterproof glue to strengthen the waterproof effect of the connection point.
4. Power supply for flexible light bar
The general voltage of the LED flexible light bar is DC 12V, so a switching power supply is required. The size of the power supply is calculated according to the length and power of the LED flexible light bar. You can also buy a high-power switching power supply as the main power supply, and connect all the LED flexible light bar input power in parallel, and the main switching power supply is used to supply power.
5. Use amplifier for LED flexible light bar
If the connection distance of the LED light bar is long, and the controller cannot control that long light bar, it is necessary to use a power amplifier for tapping.
6. Power connection method of LED flexible light bar
LED light bars generally have three voltages: AC220V, DC12V, and DC24V, so you need to choose a suitable switching power supply. The size of the power supply is determined by the power and connection length of the LED light bar. Monochrome 3528 patch and 5050 patch, the wiring method of LED lights DC24V and DC12V is as follows: black wire replaces negative "-", red wire replaces positive "+", and a soldered "red and black" power cord is provided, Just plug it directly into the light strip switching power supply provided. The black wire is connected to the negative "-" of the switching power supply and the "red" color wire is connected to the positive "+" of the switching power supply.
question&answers:
Q: Which led chips are used in this type module?
A: 22Lumen SMD5050 used for this type
Q:What Controller for this type strip?
A:very single color
Q:How many quantities module in one Roll?
A:5meters/15meters/50meters
Q:How long can i get the sample?
A: need 3-5days to send sample.
Q: Do you have MOQ limit for order ?
A:Not limit the MOQ. just depend on clients demand.
